|
Printrboard G2
|
|
6
|
49
|
September 23, 2020
|
|
Resuming after the power loss
|
|
0
|
27
|
September 16, 2020
|
|
3D printer Z height
|
|
0
|
30
|
August 24, 2020
|
|
3D printer touch screens
|
|
2
|
44
|
August 4, 2020
|
|
One of my drivers shorted. Can I save the board?
|
|
6
|
87
|
July 27, 2020
|
|
Looking for some tips for working with rasters on 5w diode based machine
|
|
3
|
92
|
June 14, 2020
|
|
Tricky coupling mechanism
|
|
2
|
78
|
May 29, 2020
|
|
"Brittle" PLA prints - layers not sticking together.
|
|
12
|
1545
|
April 11, 2020
|
|
Printer pauses for about 1/3 second at corners - leave huge blobs!
|
|
4
|
78
|
April 8, 2020
|
|
Autolevel not working after update
|
|
10
|
289
|
March 2, 2020
|
|
Game pieces
|
|
5
|
138
|
January 9, 2020
|
|
Trouble updating the firmware
|
|
0
|
91
|
October 26, 2019
|
|
Low-budget 3D sensor
|
|
0
|
88
|
November 19, 2019
|
|
Help with Print Quality
|
|
9
|
285
|
October 20, 2019
|
|
Marlin firmware set up
|
|
0
|
125
|
June 15, 2019
|
|
Issues with getting printer with Smoothieboard running
|
|
34
|
1502
|
June 6, 2019
|
|
Need a source of glass print bed
|
|
4
|
197
|
April 15, 2019
|
|
Setting height on Anycubic Kossel Linear Plus with Marlin 1.1.9 does NOT save settings
|
|
0
|
311
|
April 9, 2019
|
|
I am planning to use Ribbon cable for my 3D printer
|
|
16
|
690
|
March 29, 2019
|
|
Uneven Z plane surface
|
|
7
|
236
|
March 23, 2019
|
|
Print bed leveling and quality problems
|
|
5
|
150
|
March 19, 2019
|
|
Am I squirting too much or too little filament?
|
|
14
|
130
|
March 13, 2019
|
|
So where is everybody going? MeWe or makerforums?
|
|
14
|
124
|
March 3, 2019
|
|
I dont like using the word 'best' for anything but lets just allow me
|
|
5
|
69
|
March 2, 2019
|
|
MOON SHOT! Ideas Needed!! i just read the email below from one of our
|
|
6
|
81
|
March 1, 2019
|
|
It is my first time I need to switch from my beloved reliable low
|
|
7
|
69
|
February 17, 2019
|
|
Need Help Fixing Heater Error I recently installed an all-metal hot end for my
|
|
4
|
67
|
January 19, 2019
|
|
Ok, here's my noob-question:
|
|
20
|
168
|
February 13, 2019
|
|
Appreciate the efforts of the conductor of this community who was ThantiK during those
|
|
13
|
78
|
February 6, 2019
|
|
Quick survey - We have a hotend and it has a PCB mounted on
|
|
13
|
76
|
February 3, 2019
|
