|
About the Discussion category
|
|
0
|
121
|
February 3, 2019
|
|
My K40 has arrived. Notice anything glaring?
|
|
116
|
408
|
January 20, 2021
|
|
K40 wiring problems
|
|
8
|
71
|
January 17, 2021
|
|
Cutting on a honeycomb bed questions
|
|
2
|
31
|
January 13, 2021
|
|
K40 slider wont move smoothly
|
|
9
|
41
|
January 12, 2021
|
|
Walmart grocery loading person thinks I'm nuts
|
|
24
|
127
|
January 10, 2021
|
|
Air Assist Hose
|
|
6
|
44
|
January 10, 2021
|
|
Make Nashville K40
|
|
7
|
67
|
January 7, 2021
|
|
Sealing case questions
|
|
5
|
37
|
January 6, 2021
|
|
UK K40 Purchase
|
|
5
|
224
|
January 1, 2021
|
|
K40 lps
|
|
24
|
56
|
December 20, 2020
|
|
M2Nano Board not seen through USB/ethernet remote print bridge
|
|
23
|
111
|
December 20, 2020
|
|
Facing Some Issue In K40
|
|
3
|
58
|
December 19, 2020
|
|
K40 Tube
|
|
13
|
147
|
December 16, 2020
|
|
Hello everyone! I'm sorry if I'm posting this in the wrong place.
|
|
14
|
90
|
December 5, 2020
|
|
Is there any way to adjust the steps per mm setting on the M2 nano
|
|
8
|
507
|
November 29, 2020
|
|
Water coolant temperature and condensation
|
|
2
|
58
|
November 24, 2020
|
|
Blur on new laser cutter
|
|
5
|
51
|
November 22, 2020
|
|
Why orange plastic for CO2 lasers?
|
|
27
|
238
|
November 13, 2020
|
|
K40 expansion
|
|
0
|
72
|
November 12, 2020
|
|
Does this form of kinematics have a name?
|
|
12
|
392
|
November 1, 2020
|
|
So this is what i found at the end of the tube exit would
|
|
28
|
214
|
October 31, 2020
|
|
Using laser cutters for casting pewter
|
|
3
|
106
|
October 17, 2020
|
|
K40 water temp
|
|
3
|
128
|
October 1, 2020
|
|
Material Suggestions for Laser Cut Gears Please
|
|
5
|
107
|
September 28, 2020
|
|
Cone pin laser bed?
|
|
5
|
121
|
September 3, 2020
|
|
Coolant additives
|
|
2
|
130
|
August 20, 2020
|
|
Help Pls! Prev Burns to 12% higher no burn, New Flyback, ammeter fit, just pink glow, no power/burn
|
|
18
|
130
|
August 9, 2020
|
|
Cloudray laser head set differences?
|
|
1
|
204
|
July 15, 2020
|
|
Water Flow Failure, No Longer Firing
|
|
12
|
143
|
July 8, 2020
|
