|
About the Show & Tell category
|
|
1
|
75
|
February 24, 2019
|
|
This seller may be able to make custom beds for the Eustathios! I have
|
|
9
|
131
|
January 14, 2019
|
|
Top panel finally done! Ran this guy 22 hours a day for a month
|
|
2
|
98
|
November 7, 2018
|
|
Its been kind of quiet in here lately...figured I would throw this out there
|
|
6
|
128
|
October 4, 2018
|
|
It has been awhile,
|
|
3
|
83
|
September 5, 2018
|
|
Needed something to print,
|
|
31
|
165
|
April 14, 2018
|
|
Enclosure Three years after I started the build,
|
|
5
|
108
|
April 4, 2018
|
|
If any of you are looking for a Bondtech on a discount hit up
|
|
1
|
86
|
April 1, 2018
|
|
MRRF is a blast!
|
|
3
|
83
|
March 24, 2018
|
|
Last night during a print the heater cartridge on my hotend must have caused
|
|
12
|
75
|
March 23, 2018
|
|
Its not pretty, but its a print.
|
|
16
|
127
|
March 15, 2018
|
|
I have inconsistent layer registration.
|
|
11
|
80
|
March 15, 2018
|
|
First print in the books. Everything was going so well until the end there...
|
|
6
|
80
|
March 10, 2018
|
|
Does a parts cooling fan make a difference; YES! Before: After:
|
|
4
|
73
|
March 4, 2018
|
|
It Lives! After wrestling with configuring Marlin and cleaning up some wiring,
|
|
4
|
112
|
February 23, 2018
|
|
Enclosure for the Smoothieboard.
|
|
7
|
108
|
February 22, 2018
|
|
Just wanted to some honey comb fun for a part I am designing for
|
|
5
|
65
|
February 19, 2018
|
|
Here are some photos of the cracking.
|
|
19
|
236
|
February 14, 2018
|
|
So enjoying learning all about printing, infill, etc.
|
|
1
|
79
|
February 10, 2018
|
|
Well, after quite a few attempts, and lots of questions,
|
|
3
|
117
|
February 6, 2018
|
|
It does not look pretty,
|
|
5
|
68
|
January 25, 2018
|
|
And now that she is pretty much done, here is a Marvin at 500%.
|
|
5
|
83
|
November 28, 2017
|
|
The Hybrid. Always had bad z wobble with the increased height,
|
|
2
|
72
|
November 14, 2017
|
|
So I'm finally at a point where I have a working derivative/custom Eust.
|
|
8
|
90
|
November 12, 2017
|
|
McGyver workaround for a broken part
|
|
7
|
69
|
July 1, 2017
|
|
Well, the lid is done (still got the door to do)
|
|
1
|
80
|
May 30, 2017
|
|
quick mod on the Herculien.
|
|
2
|
68
|
May 24, 2017
|
|
500 mm/s ;) :
|
|
4
|
87
|
April 20, 2017
|
|
Got home today to a nice Little surprise.
|
|
6
|
96
|
April 14, 2017
|
|
Hey everyone. Printing on my Eusthatios is getting better as my hotend cooling is
|
|
13
|
153
|
April 2, 2017
|
